KLEIN TOOLS 60347 KARBN Full Brim Helmet Instruction Manuals+ (2023)

KLEIN TOOLS 60347 KARBN Full Brim Helmet Instructions

EMBARGO!BEFORE USE: READ ALL INSTRUCTIONS OR YOU ARE RISK OF SERIOUS INJURY OR DEATH. DO NOT REMOVE THE LABEL

• This headgear is designed to absorb some of the energy of a blow by partially destroying its components, and while the damage may not be apparent, any headgear subjected to a hard impact must be replaced.
• This protective cover must not be painted or cleaned with solvents. All decals applied to the helmet must be compatible with the surface material and are known not to adversely affect the characteristics of the materials used in the helmet.
• Any structural additions or modifications may reduce the protective properties offered by this protective cover.

TO USE:This label is representative; content varies by model.

GENERAL SPECIFICATIONS

• Housing Material: PC/ABS Composite
• Surface pattern: hydro-dipped polymer film
• Standards: Klein Tools KarbnTM helmets meet ANSI Type I/
  ISEA Z89.1-2014, CSA Z94.1-15:
  • Class E ventless helmets have been tested up to 20 kV.
    EN397:2012+A1:2012 (listed clauses only):
  • 5.2.4-Lateral Deformation (LD)
    EN12492:2012 (numbered clauses only):
  • 4.2.1.2-Front Energy Absorption Capacity
  • 4.2.1.3- Lateral energy absorption capacity
  • 4.2.1.4-Rear energy absorption capacity
• Fits:Head Sizes 6-1/2 to 8 (20-1/2 to 25 inches / 52 to 64 cm)

SYMBOLS ON THE PRODUCT

(FIG. A

1. reverse positioning logo
2. Information on supported standards, class, head type and size
3. Recycling code and material type
4. Manufacturing date

NOTICE SIGNS

FIGO. B.

There are two warning labels attached to the inside of this helmet. Read, understand and follow these instructions to ensure safe operation. DO NOT REMOVE THESE LABELS.

NOTICES

READ ALL INSTRUCTIONS. FAILURE TO FOLLOW THESE WARNINGS AND INSTRUCTIONS COULD RESULT IN SERIOUS BODILY INJURY OR DEATH.

• This helmet offers LIMITED protection against small objects striking the top, front, back, left and right sides of the helmet. This is NOT an ANSI/CSA Type II helmet.
• DO NOT expose suspension and filling to open flames.
• ELECTRICAL WARNING: Avoid areas where the possibility of electrical shock exists. Unventilated versions meet Class E requirements providing limited electrical protection. Class C vented models DO NOT provide electrical protection.
• If the helmet has suffered an impact, discard it IMMEDIATELY, even if the damage is not visible.
• NEVER alter, drill, modify or etch the housing or suspension.
• DO NOT use paints, solvents, chemicals, adhesives, gasoline or similar substances on this helmet; this can decrease the protection provided against impact and penetration.
• DO NOT use this helmet as a vehicular or recreational helmet.
• DO NOT store objects between the suspension and frame as the helmet will not perform as expected and may decrease impact and penetration protection.
• Exposure to direct sunlight, corrosive environments and/or temperature extremes below -40°F (-40°C) or above 120°F (49°C) can decrease the helmet's ability to withstand impact and penetration.

FEATURE DETAILS

FIG.C

5🇧🇷 Universal Accessory Slots 12 Washable sweatband
6Washable superior comfort pad with 13 compartments for Klein Tools accessories
7Openings with shutters
(Class C only) 14 Suspension straps
8Pivot adjustment 15 reflective stickers
9Size Adjustment Knob 16 Hanger Holder
10Back neck pad 17 Key support
11Suspension Strap Anchor Slots 18 Bracket Wrench Slots
12washable sweat band
13Washable superior comfort pad
14hanging straps
15reflective stickers
sixteensuspension bracket
17support key
18Supports key slots

APPROPRIATE

FIGO. D.

All helmets come with suspension pre-installed in the factory configuration. The suspension can be adjusted to ensure a proper and secure fit to your head for maximum protection. Follow the steps below:

PASO 1: Turn the size adjustment knob 9 counterclockwise to loosen the setting. Place the back pillow at the back of the head, closest to the neck. Hang bandana knots or ponytails over the back of your neck 10 .

PASO 2: Tighten by turning the size adjustment knob 9 clockwise until the helmet is snug and snug. Move your head up, down and side to side smoothly as you normally would and make sure the helmet stays on. Make sure the helmet is not tilted forward or backward, but is resting on your head.

DEFINITIONS

FIGO. Y

If the helmet does not fit correctly in the factory settings, you can further adjust the fit.

PASO 1: Release bracket by rotating bracket bracket 16 approximately 90 degrees to release bracket key 17 from bracket key slots.

PASO 2: Determine which slot 18 you want to reconnect to. Using the deeper support slots in the helmet will move it higher on the head and vice versa. Insert Bracket Key 17 and rotate Bracket 16 approximately 90 degrees to lock it in place. Always match left and right side adjustments to prevent the suspension from slanting.

PASO 3: Make sure the helmet fits correctly. Follow the steps in the FITTING section to ensure a proper fit. Make sure the accessories you plan to use fit and function properly, maintaining the helmet's ability to perform its function optimally. Consult a qualified security expert if you are unsure.

TO USE:The lengths of the suspension straps are fixed and cannot be adjusted. DO NOT try to change.

SUSPENSION REPLACEMENT

STEP 1:Place index finger under strap anchor and thumb over anchor groove 11 . Push up with index finger using enough force to release anchor from slot. Do this for all anchor slots (4 total). NOTE: DO NOT pull on the suspension straps to release the anchor. Doing so can permanently damage the belts, preventing them from working as intended.

PASO 2: Make height adjustments to the new suspension before installation.

PASO 3: Push each anchor down until it clicks and the anchor can no longer be pushed down. Do this for all 4 anchors. NOTE: DO NOT use sharp tools that could damage the anchors or pull the straps to secure them.

PASO 4: Check for proper installation by pushing up all 4 anchor pads. Anchors must remain fully engaged in their slots. Otherwise, repeat STEP 3.

STEP 5:Make sure the helmet fits correctly. Follow the steps in the FITTING section to ensure a proper fit. Also make sure that any accessories you plan to use fit and function properly, maintaining the helmet's ability to function optimally.

SUPERIOR COMFORT SWEATBAND AND CUSHION

FIG.H

FANS (CLASS C ONLY)

Klein Tools Class C helmets have vents and louvers on both sides. Apertures can be adjusted by simply sliding the shutter tabs 7 up or down.

Warning:Vents and louvers will NOT prevent vapors, liquids or debris smaller than the vents from entering the helmet.

56048 FARO

The Klein Tools 56048 rechargeable headlamp offers three modes: 22-hour floodlight; Spotlight focused for 12 hours, 400 lumens All-On mode. 56048 features an LED battery indicator that indicates remaining battery life and an auto-off sensor that turns the headlight off in bright light or outdoors where additional headlight lighting is not required, to extend headlight life.

19release guide
20On/off/mode button
21stand out
22flood lights
23Support
24pivot assembly
25charging port cover
26Light sensor

The 56048 can be attached to the front or back of the helmet via the Klein Tools accessory slot. It can be tilted up to 64 degrees on the helmet and function as a work light.

To install the headlamp on a Klein helmet, align the pivot bracket 24 with the Klein Tools accessory slot 6 in the helmet and push down until the headlamp clicks into place.

To remove headlight, push release tab 19 forward and lift headlight out of accessory compartment.

REFLECTIVE STICKERS

Hello. Ç

Klein Tools KarbnTM helmets come with 15 reflective stickers installed. These have been tested and found to be compatible with this helmet.

WARNING:Klein Tools DOES NOT condone the application of metal-containing adhesives, hot stamps, paints and metallic foils to this helmet by end users. Such modifications may alter the performance of the helmet.

MAINTENANCE

HARD HELM CLEANING AND STORAGE

• Clean the hull and suspension with water and mild soap only. Rinse and dry. Clean the optional chin strap with a damp cloth only. Store in a cool place.
• Refer to the SUITE STRAP AND SUPERIOR COMFORT CUSHION section of the Operating Instructions (Opposite Side) for additional maintenance information.

INSPECTION AND REPLACEMENT

Inspect the helmet, including suspension and frame, before and after each use:

• Inspect the helmet shell for cracks, breaks, discoloration, chalky appearance or any other damage, excessive wear or unusual condition. These conditions may indicate reduced impact or penetration resistance and the helmet should be replaced IMMEDIATELY.
• Suspension and optional chin strap should be checked for cracks, tears, damaged stitching or any other damage, excessive wear or unusual condition. If any of these conditions exist, the suspension and optional chin strap must be replaced IMMEDIATELY.
• Always use genuine Klein Tools replacement parts. This product works as a system and the use of unauthorized suspensions can reduce the protection you receive from this helmet.

USEFUL LIFE

OPTIONAL CHIN SUSPENSION AND STRAP: Must be replaced after a maximum of 12 months of use.

FULL HELMET: The entire helmet must be replaced after a maximum of 2 years of regular use or 5 years from the date of manufacture, whichever comes first.
These are the MAXIMUM life guidelines. Regular inspection MUST be performed as detailed in the MAINTENANCE section above and may result in possible sooner replacement.
TO USE:This replacement schedule is a guideline that assumes normal helmet use and storage. If the helmet has been exposed to extreme temperatures, persistent sunlight or chemicals, it may need to be replaced in a shorter period of time.

ACCESSORIES AND SPARE PARTS

Accessories and replacement parts for Klein Tools helmets are available online or from major distributors:

• KHHSPN2: Premium Replacement Suspension
• KHHSWTBND2: Premium Bracelet (3-Pack)
• KHHTOPPAD2: Premium Superior Comfort Cushion (3-Pack)
• KHHSTRP: chin strap
• 56048: Rechargeable Headlight with Auto Shut-off (Spot/Flood/All On)
• 56049: Rechargeable light kit headlamp (flood only)
• 56062: Rechargeable Headlamp/Magnetic Work Light (Spot/Flood)

TO USE:KLEIN TOOLS CANNOT GUARANTEE THAT THIRD PARTY ACCESSORIES WILL WORK OPTIMALLY OR FIT WITH THE KLEIN TOOLS HARD HELMET.

DISPOSAL / RECYCLING

Do not throw the helmet or its accessories in the trash. Items must be disposed of properly in accordance with local regulations. To seewww.epa.govfor additional information.

WARRANTY

www.kleintools.com/warranty

CUSTOMER SERVICE

KLEIN TOOLS, INC.
450 Bond Street, Lincolnshire, IL 60069 1-800-553-4676
[email protected]
www.kleintools.es

Documents / Resources